Listed here below yow will discover additional first-rate insights around How to Install a Bathtub.
Installing a tub isn't specifically rocket science, however it does call for strong plumbing, carpentry, as well as often, tiling abilities. Replacing an old bathtub with a new one is likewise a reasonably challenging task. If the old tub is easily easily accessible, the project can relocate speedily; if you need to open a wall surface to get rid of the old tub and also place the brand-new bathtub, the task is much harder. In either instance, the task is within a house handyman's skills, although you will certainly require an assistant to move out the old bathtub and embeded in the new one. Make sure you have actually qualified on your own for the task as well as fit attempting it. As opposed to hiring a professional to take control of a halfway-completed task, it is much better to take into consideration utilizing one before you start. Possibilities are you may need an expert plumber to make tube links.
This write-up will certainly help you install a new bath tub in your washroom if you have actually currently gotten a new tub and also do not need to change the arrangement of your previous supply of water pipelines.
Your devices as well as material list ought to consist of the following:
Planning for the Installment
To start with, the supporting frame provided with the bathroom ought to be fitted (if called for) according to the manufacturer's directions. Next off, fit the taps or mixer to the bath tub. When suitable the faucet block, it is necessary to see to it that if the tap includes a plastic washing machine, it is fitted in between the bathroom and also the taps. On a plastic bath, it is also practical to fit a sustaining plate under the taps device to avoid strain on the bath tub.
Fit the versatile faucet connectors to the bottom of both faucets using 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Make sure you utilize all of the supplied washing machines.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom should now be ready to be fitted in its last placement.
Removing Old Taps
If you need to change old taps with new ones as a part of your setup, after that the first thing you need to do is separate the supply of water. After doing so, turn on the faucets to drain pipes any type of water continuing to be in the system. The process of eliminating the existing taps can be rather problematic due to the restricted accessibility that is typically the instance.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a fabric prepared for the continuing to be water that will certainly originate from the pipes. Once the supply pipelines have actually been removed, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from transforming during this procedure. As soon as the taps have been removed, the holes in the bath/basin will certainly have to be cleaned up of any old securing compound.
Prior to proceeding to fit the brand-new taps, compare the pipeline connections on the old taps to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Setting up the Tub
Making use of both wood boards under its feet, position the bath tub in the needed setting. The wooden boards are valuable in uniformly spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto four tiny factors.
The next objective is to make certain that the tub is leveled all round. This can be attained by checking the spirit level and also adjusting the feet on the bathtub until the spirit level checks out degree.
To set up taps, fit the bottom of the furthest versatile faucet adapter to the appropriate supply pipe by making a compression sign up with; then do the exact same for the various other tap.
Switch on the supply of water and also examine all joints as well as brand-new pipework for leaks and tighten them if necessary. Load the tub as well as likewise inspect the overflow outlet and also the typical electrical outlet for leaks.
Finally, repair the bathroom paneling as explained in the producer's user's manual. Tiling as well as sealing around the bath tub should wait until the bathtub has been made use of a minimum of once as this will certainly settle it into its last placement.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will certainly need a plastic connector to prevent damage to the string. One end of the port fits on the plastic tail of the tap and also the various other end supplies a connection to the current supply pipelines.
If you need to fit a monobloc, then you will certainly need minimizing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the installing opening in the bath/basin making sure that the washing machines are in location in between the faucet as well as the sink. Protect the faucet in position with the producer offered backnut. When the tap is firmly in place, the supply pipes can be connected to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with regular tap connectors. The previous type ought to be connected to the tap finishes initially, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the area where the bathroom meets the tile, it is essential to seal the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to fracture a rigid seal, creating the water to permeate the wall surface between the bathroom and also the tiling, causing problems with moisture and possible leaks to the ceiling below.
You can pick from a range of coloured sealers to assimilate your fixtures and also installations. They are offered in tubes and cartridges, as well as can sealing voids up to a size of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked newspaper or soft rope. Remember to always fill up the bath tub with water prior to securing, to allow for the movement experienced when the tub is in use. The sealer can fracture rather very early if you do not think about this activity before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally quickly available on the marketplace. It is a good idea to fit the ceramic tiles using waterproof or waterproof glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a keen reader on How to Install a Bathtub Yourself, I was thinking sharing that short article was a great idea. Sharing is caring. Helping people is fun. We enjoy reading our article about Installing A Bathtub.
Your solution? Just a ring.